Transmission oil drain plug question . . .
I picked up four quarts of ATF-Z1 today, and plan on doing a drain/fill.
Does the oil plug require any special attention upon reinstallation? Is there a crush ring on the plug? I didn't get one at the dealer, nor did they suggest one. On a lighter note, in the last week I've done the plugs and engine/cabin air filters. This was the first changing of the cabin air filter! Guess the last owner [my brother] was too busy! |
To do a drain/fill you need nine quarts. It is a 3x3 procedure.
There is a crush ring but it is likely it does not need to be replaced. |
3X3 is for a complete (almost) changeover. For normal maintenance, a 3.5qt change is fine.
|
its about 3.2 qts will drain out with trans warm from 15 minute drive- then start the draining
remove trans dipstick to allow air thru- just like oil change most years have a drainplug that you insert a 3/8" ratchet into - a square place in the center of the drain plug and its lefty loosie to remove- not a regular looking bolt type as the engine oil does Note ATF is stamped above drain so you cant go wrong Suggest you test plug before getting it hot- can seem to be way too tight from years of sitting. Break it loose then retighten to 29 foot pounds, same as oil drain plug If stuck try tightening slightly then remove Make sure you can get it loose before anything else! make sure to put back same amount- over filling is really bad for the trans Follow book procedure to ck level- 10-15 minutes on freeway cruising- then get off and stop on level safe place. STOP ENGINE and pull dipstick- wipe clean and reinsert- remove and now read Level, needs to be in between the dots or lines- anywhere in between is good- towards the middle is better. appearent Level rises with more heat from driving, so again- do not overfill !! or drain off excess if it happens |
I suggest a full drain. If the PO was too busy to ever change the HVAC filters how likely is it he did the transmission?
I have had my car two years and almost 40k and have done three complete drain & fills. These are glass transmissions. |
Originally Posted by e30cabrio
(Post 11935888)
I suggest a full drain. If the PO was too busy to ever change the HVAC filters how likely is it he did the transmission?
I have had my car two years and almost 40k and have done three complete drain & fills. These are glass transmissions. I would actually suggest just drain/fill once. |
I'm planning on a 3qt. drain and fill. However, I've no ramps, and the plug is frozen.
It'll have to wait until I can get over to a friend's house. |
spray some wd type stuff at the edges of the plug to get in the threads
let sit overnight Now place ratchet in place and set to tighten Give that a whack or 3 with a hammer to send vibrations thru the assembly- that breaks the corrossion bond and lets you remove it |
PB Blaster is your friend....
|
You can do a 3qt change once a month for three months to ease the transition in the transmission :) Draining is easy - you don't even need ramps. A floor jack on the middle support on the front frame crossmember will lift it up plenty. Once I get my drain pan in place and the plug out, I actually lower the jack to get a little more fluid out. I raise it again to get the pan out and put the plug back in.
You need to find the refill hole/plug before starting so you don't get stuck halfway through. Do you know where it is? Do you have an oil-jet kit installed? |
I found that my fill plug was way more tight then my drain plug. In fact, I never got it loose and just filled it through the dip stick.
|
Originally Posted by jdjohn84
(Post 11937736)
Do you have an oil-jet kit installed?
Turns out these parts have not been ordered for 17 months, as most of the TLs have had it done already. I want to get set up for filling through the dip, but with a breaker bar, I was ready to have a go at both plugs. The drain stopped me dead, however. As to a jack, I'd not be inclined to work under a car without blocks or stands. However, just to reach my arm under with a longer ratchet, I guess that'd be all right. |
NEVER get under a car on a jack without a proper support!!!!!!!!!!!!!!!!!!!!,
something taller than you are thick... so if car falls it doesnt crush you~ Jacks WILL fail at the worst possible moment Compression injuries to the chest are among the worst you can try to survive!! Hint: may not survive!!!! you can try parking with left wheels on the sidewalk if you have a decent incline/drop to the street- able to slide under, and the car is on all 4 wheels |
All times are GMT -5. The time now is 08:27 PM. |
© 2024 MH Sub I, LLC dba Internet Brands