i have a question about the fogs
10-20-2010, 05:25 PM
#1
Advanced
Thread Starter
Join Date: Jan 2010
Location: Toronto
Age: 31
Posts: 64
Likes: 0
Received 0 Likes
on
0 Posts
i have a question about the fogs
i see lots of tls here with just the fogs on without the headlights..
i tried everything it works only with the headlights.
how do i do that on my TL?
i tried everything it works only with the headlights.
how do i do that on my TL?
10-20-2010, 05:58 PM
#3
hmmmmmm...oh wait... nvm.
sorry but that was funny lol
10-20-2010, 06:04 PM
#4
I'm a thrill seeker in my
Welcome to the forums man, get aquainted with the search feature near the top of the page. Use the right keywords and it will give you the answers to almost anything to do with our cars 
A quick answer that doesn't tell you how to do it basically guys re-wire things so the fog lights come on without the headlights, not tough. I'm sure there's a diy
p.s. LOL at Josh's post, always the witty douchebag comments now that you've moved on. Love it.
A quick answer that doesn't tell you how to do it basically guys re-wire things so the fog lights come on without the headlights, not tough. I'm sure there's a diy
p.s. LOL at Josh's post, always the witty douchebag comments now that you've moved on. Love it.
10-20-2010, 06:29 PM
#5
Advanced
iTrader: (1)
Join Date: Dec 2009
Location: Richmond VA by way of NY
Age: 49
Posts: 98
Likes: 0
Received 2 Likes
on
2 Posts
Yes, you would have to splice into the driveing lights, and wire the fogs into the parking lights. I had HID's running to fogs on my Cl and thats how we wired it. We also ran a relay as well. Good luck
10-20-2010, 07:03 PM
#7
op read this thread..
https://acurazine.com/forums/2g-tl-1999-2003-98/fog-light-mod-alternate-version-549015/
that way is best..
iirc, it still turns off when you high beam
loved foglight mod so much, that i did it on my genesis.. lol! except they NEVER turn off, even with the high beam on
Trending Topics
10-23-2010, 02:01 PM
#11
bringin lead
10-23-2010, 02:14 PM
#12
even better! it has words!
do you need help reading too?
do you need help reading too?
I did Elegant's car today and here are some pictures that I took for the install. 
This is what a diode looks like and how it works, current only flows from Anode to Cathode, the silver bar shows you which is the cathode side.
That is my diode connected to some wire to the left and to the right (Anode and Cathode sides) with some shrink wrap over it. Electrical tape will be fine as well. I had soldered it but you can just twist it together.
Here it is connected to the MINI add-a-circut crimped to the Anode side of the wire to the blue thing. I used a 3 AMP fuse, probably more than needed but it is fine. Notice where it is added, the instructions of the add-a-circuit will explain.
This is the fog light switch harness and swtich. I had to undo the original fog light mod and taped up the two wires.
Just another shot
Driver side Fuse panel before I remove anything.
Drive side Fuse panel after I remove the fuse #9 instrumental panel slot. The one below it is the ACC one. Both are 7.5 Amps.
With the removed fuse I just place it into the other slot of the add-a-circuit. Again the instructions of the add-a-circuit will explain.
The add-a-circuit installed into the fuse box. I just plugged it back into the fuse #9 slot. Just that easy.
Close up!
The other side now of the diode, Cathode side, now you just use a tap to tap into white/red wire which was used originally for the first fog light mod. So you crimp the black wire extended from the cathode side of the diode to the white/red wire.
Close up of how it is crimped together.
Now you are done!!!!!!!!!!!!!
This is what a diode looks like and how it works, current only flows from Anode to Cathode, the silver bar shows you which is the cathode side.
That is my diode connected to some wire to the left and to the right (Anode and Cathode sides) with some shrink wrap over it. Electrical tape will be fine as well. I had soldered it but you can just twist it together.
Here it is connected to the MINI add-a-circut crimped to the Anode side of the wire to the blue thing. I used a 3 AMP fuse, probably more than needed but it is fine. Notice where it is added, the instructions of the add-a-circuit will explain.
This is the fog light switch harness and swtich. I had to undo the original fog light mod and taped up the two wires.
Just another shot
Driver side Fuse panel before I remove anything.
Drive side Fuse panel after I remove the fuse #9 instrumental panel slot. The one below it is the ACC one. Both are 7.5 Amps.
With the removed fuse I just place it into the other slot of the add-a-circuit. Again the instructions of the add-a-circuit will explain.
The add-a-circuit installed into the fuse box. I just plugged it back into the fuse #9 slot. Just that easy.
Close up!
The other side now of the diode, Cathode side, now you just use a tap to tap into white/red wire which was used originally for the first fog light mod. So you crimp the black wire extended from the cathode side of the diode to the white/red wire.
Close up of how it is crimped together.
Now you are done!!!!!!!!!!!!!
Thread
Thread Starter
Forum
Replies
Last Post
navtool.com
5G TLX Audio, Bluetooth, Electronics & Navigation
31
11-16-2015 08:30 PM
navtool.com
1G RDX Audio, Bluetooth, Electronics & Navigation
1
09-25-2015 05:15 PM